---

Index Page

Mack Corp. Home

Previous Page

Next Page

Wall Chart

Click robot for printer friendly page

---

Data Sheet 9136 Page 6

SHORT STROKE PNEUMATIC CYLINDERS, LO-PROfile® SERIES A-SP-FM
Single Acting - Spring Extending - Single Ended Pistons - Side Ported - Either Face Mounted

SPECIFICATIONS: Service: Plant Air M.O.P: 300 PSI Temp: -40 to +250 deg. F

Materials: Body: Aluminum Alloy Covers: Aluminum Alloy Piston: Stainless Steel

Springs: Music Wire Seals: Buna "N" O-Rings Fasteners: Alloy Steel

Basic Part No.  O.D. A  Bolt Circle B  Rod Dia. C  Rod Thd. D  Wrench Flats E  spring pocket F  Piston O.D. (IN)  Net Piston Area (SQ. IN)  Nom. Force (lbs) = Pressure (psi) times Area (sq. in.) NOTES: Dimensions are nominal in U.S. Customary units. Metric versions are dimensionally equivalent except for conversion in mounting details where fasteners, threads, clearance holes & counter-bores are to metric standards. To see a table of U.S. Customary to Metric fastener conversion, click here . There is no added cost for this metric modification. An air/oil mist unit is recommended for internal lubrication. Where such units are not practical, SERVICE KITS including seals and factory approved lube are available. Cylinders may also be used in low pressure hydraulic service. Wrench flats may not be necessary if cylinders can be pressurized in the retracted or extended position while tightening the rod joint. Inquiries regarding modification to BASIC CYLINDERS are always welcome.

---

Index Page

Mack Corp. Home

Previous Page

Next Page

Wall Chart

Click robot for printer friendly page

---

To request a quote for a unit on this page, please fill out the following form and submit.

REQUIRED ENTRIES

US Standard Metric

Material: Default (see above specifications) S - All Stainless Steel

1) Please enter the BASIC PART NO:

2)PISTON TRAVEL
US Standard Click Here 1 (0.100) 2 (0.200) 3 (0.300) 4 (0.400) 5 (0.500) 6 (0.600) 7 (0.700) 8 (0.800) 9 (0.900) 10 (1.000) (shown in 1/10 inch increments, maximum 1.000 in. for spring extending cylinders.)
Metric Click Here 2.5mm 5.0mm 7.5mm 10.0mm 12.5mm 15.0mm 17.5mm 20.0mm 22.5mm 25.0mm (shown in 2.5mm increments, maximum 25.0mm. for spring extending cylinders.)

OPTIONAL ENTRIES

3) MOUNTING STYLE:
Default CBB -Thru clearance holes with c'bores in the body for no. 4-40 I.S.H.C.S. at 4 locations. FL - This cover is larger for flange mounting to either side. T - Mounting directly to the user's structure provides the lowest overall height. TC - Alternate mounting to user's structure to provide minimum overall height.

Default Click here for extra info.

CBB -C'bore in the body. Click here for extra info.

FL - Flange mounting. Click here for extra info.

T - Mntng to user's structure. Click here for extra info.

TC -Mntng to user's structure. Click here for extra info.

4)ROD ENDS: Default (see above drawing) ITW - Internal Threads with Wrench Flats ETW - External Threads with Wrench Flats

ITW - Internal Threads with Wrench Flats

ETW - External Threads with Wrench Flats

Note: Spring force for BASIC CYLINDERS is sufficient to fully retract pistons. Higher spring force may be required
for retracting loads attached to rod ends. Please consult the FACTORY.

5) PORTS: Default (1/16 NPT Port) 10-32 - (U.S.A. 10-32 Threaded Ports. Straight thread, flat gasket sealing.)

6) O-Ring Option:

Default (Buna "N" O-rings, -40ºF. To +250ºF.)
Viton "O"rings (-15ºF. To +400º F.)

7) Quantity:

8) Customer Information

Name
Title
Company
Address
City
State/Province
Country
Zip Code
Telephone

Fax
Email

Comments

Data Sheet 9136
Page 6

---

Index Page

Mack Corp. Home

Previous Page

Next Page

Wall Chart

Click robot for printer friendly page

---

Copyright Information

Privacy Statement

Warranty

© 2000 Mack Corporation