---

Index Page

Mack Corp. Home

Previous Page

Next Page

Wall Chart

Click robot for printer friendly page

---

Data Sheet 9932 Page 32

SPECIFICATIONS: Service: Plant Air M.O.P: 150 PSI Temp: -40 to +250 deg. F

Materials: Body: Aluminum Alloy Cap: Aluminum Alloy Piston: Stainless Steel

Bushing:Oil filled bronze Seals: Buna "N" O-Rings

Basic Part No. A  B C  D  E  F  G  H  J  Nom. Force (lbs) = Pressure (psi) times Area (sq. in.) Basic Part No.   K    L    M    N    P  Piston Dia. (IN) Ext. Piston Area (SQ.IN.) Retr. Piston Area (SQ.IN.)  Nom. Force (lbs) = Pressure (psi) times Area (sq. in.) NOTES: Dimensions are nominal in U.S. Customary units. Metric versions are dimensionally equivalent except for conversion in mounting details where fasteners, threads, clearance holes & counter-bores are to metric standards. To see a table of U.S. Customary to Metric fastener conversion, click here . There is no added cost for this metric modification. An air/oil mist unit is recommended for internal lubrication. Where such units are not practical, SERVICE KITS including seals and factory approved lube are available. Cylinders may also be used in low pressure hydraulic service. Wrench flats may not be necessary if cylinders can be pressurized in the retracted or extended position while tightening the rod joint. Inquiries regarding modification to BASIC CYLINDERS are always welcome.

---

Index Page

Mack Corp. Home

Previous Page

Next Page

Wall Chart

Click robot for printer friendly page

---

To request a quote for a unit on this page, please fill out the following form and submit.

REQUIRED ENTRIES

US Standard Metric

Material: Default (see above specifications) S - All stainless steel

1) Please enter the BASIC PART NO:

2)PISTON TRAVEL
US Standard Click Here 1 (0.100) 2 (0.200) 3 (0.300) 4 (0.400) 5 (0.500) 6 (0.600) 7 (0.700) 8 (0.800) 9 (0.900) 10 (1.000) 11 (1.100) 12 (1.200) 13 (1.300) 14 (1.400) 15 (1.500) 16 (1.600) 17 (1.700) 18 (1.800) 19 (1.900) 20 (2.000) (shown in 1/10 inch increments, maximum 2.000 in.)
Metric Click Here 2.5mm 5.0mm 7.5mm 10.0mm 12.5mm 15.0mm 17.5mm 20.0mm 22.5mm 25.0mm 27.5mm 30.0mm 32.5mm 35.0mm 37.5mm 40.0mm 42.5mm 45.0mm 47.5mm 50.0mm (shown in 2.5mm increments, maximum 50.0mm.)

OPTIONAL ENTRIES

3) MOUNTING OPTION: Default (see above drawing) IT - Body is threaded internally for mounting with "H" fasteners from below. CBB - Clearance holes are counterbored for "H" int. sock. hd. cap screws.

IT- Internal threads in the body.

CBB - Clearance holes counterbored.

4)ROD ENDS: Default (see drawing) ITW - Internal Threads with Wrench Flats ETW - External Threads with Wrench Flats

ITW - Internal Threads with Wrench Flats

ETW - External Threads with Wrench Flats

5) Quantity:

6) Customer Information

Name
Title
Company
Address
City
State/Province
Country
Zip Code
Telephone

Fax
Email

Comments

Data Sheet 9932
Page 32

---

Index Page

Mack Corp. Home

Previous Page

Next Page

Wall Chart

Click robot for printer friendly page

---

Copyright Information

Privacy Statement

Warranty

© 2000 Mack Corporation