Index Page Mack Corp. Home Next Page Wall Chart Click robot for printer friendly page
Data Sheet 9261 Page 1


TWO FINGER B•A•S•E® GRIPPERS - SER. 2

Two finger grippers simulate the motions of the thumb and index finger for reaching into channels, grasping parts in confined space or picking and placing objects of simple geometry. Positioning an object in the plane of the fingers is inherently good. Positioning in a plane perpendicular to the fingers is not controlled unless the work piece has a shoulder or is presented to the gripper in a uniform way.
•BASIC TWO FINGER UNITS - WITHOUT FINGERS

Basic
Part
No. 


A


B


C


D


E


F


G


H


J


K


L


M


N


P


Q


R
  

P = Net piston area in square inches.
Q = Weight of unit in ounces.
R = Mounting flange identification. Click here to see Gripper Tech Data Sheet No. 9265
•TWO FINGER UNITS - WITH BLANK FINGERS

Basic
Part
No. 


A


B


C


D


E


F


G


H


J


K


L
  

H = Gripper weight in ounces.
J = Pinch force in pounds at 8/10 F with inlet pressure of 80 PSI.
K = Finger rotation in degress.
L = Mounting flange identification. Click here to see Gripper Tech Data Sheet No. 9265
•TWO FINGER UNITS - WITH INTERNAL GRIPPING FINGERS

Basic
Part
No. 



A




B




C




D




E




F




G




H




J




K
  

G = Gripper weight in ounces.
H = Pinch force in pounds at contact points with inlet pressure of 80 PSI.
J = Finger rotation in degress.
K = Mounting flange identification. Click here to see Gripper Tech Data Sheet No. 9265
•TWO FINGER UNITS - WITH EXTERNAL GRIPPER FINGERS

Basic
Part
No. 


A


B


C


D


E


F


G


H


J
  

F = Gripper weight in ounces.
G= Pinch force in pounds at contact points with inlet pressure of 80 PSI.
H = Finger rotation in degress.
J = Mounting flange identification. Click here to see Gripper Tech Data Sheet No. 9265

SPECIFICATIONS:
SERVICE: Plant Air
M.O.P: 150 PSI (10 BARS)
M.O.T: +250º F. (120ºC.)		 Materials:
Piston: Stainless Stl.
Stem: Stainless Stl.
Pins: Stainless Stl.		 Housing: Aluminum Alloy
Fingers: Aluminum Alloy
Seals: Buna "N" O-Ring
Fasteners: Alloy Steel

Dimensions are nominal in U.S. Customary units.
Metric versions are dimentionally equivalent with clearance holes, counterbores bores, threads and fasteners to metric standards. Click here for U.S.A to Metric thread conversion.
An air/oil mist unit is recommended for internal lubrication. Where such units are not practical, service kits including seals and factory approved lube are available.
Grippers may be used in low pressure hydraulic service and in vacuum ambients.
Fingers may be fabricated from any machinable material with physical properties of 20,000 psi or higher.
Please refer to the view & tabulated data on BASIC UNITS WITHOUT FINGERS for dimensions not shown. See TECH DATA SHEET 9265 for added information on grippers.

Index Page Mack Corp. Home Next Page Wall Chart Click robot for printer friendly page

To request a quote for a unit on this page, please fill out the following form and submit.

 

REQUIRED ENTRIES

US Standard
Metric

Material:
Default (see above specifications)
SS - All stainless steel grippers.

1) Please enter the BASIC PART NO:

2) OPTIONS: Check all options that you would like with your gripper(s).

S - Grippers with Stainless Steel fingers.
SFTS - Spare Tool Steel fingers.
SFA - Spare Aluminum fingers.
SFS - Spare Stainless fingers.
TS - Grippers with Tool Steel fingers.
V - Grippers with Viton seals.

3) Fittings and Ports
Two piece Mono-Taper™ elbows are supplied. Mono-Taper™ fittings are rugged, miniature fittings based on S.A.E 1/4-28 standards where all taper is incorporated into the fitting. Ports are 1/4-28 internal straight threads.

Fitting locations in the body is on section Y-Y & the fitting location in the cover may be oriented to any 90º relationship to section Y-Y. Two pieces elbows for 1/8" I.D. plastic tubing are supplied unless one of the options below is required.

To dress Control Lines radically outward, disassemble elbows & install only the Barbed section.
An option elbow for 1/16" I.D. plastic tubing.
To dress 1/16" I.D. plastic tubing radially outward, disassemble two piece elbow & install only the barbed section.
10-32 straight threaded optional ports.


4) Quantity:

 

5) SERVICE KITS:
SK - Buna "N" service kit. Basic Part Number: Quantity:

VSK - Viton Service Kit. Basic Part Number: Quantity:



 

6) Customer Information:

Name
Title
Company
Address
City
State/Province
Country 
Zip Code
Telephone

Fax
Email


Comments


Please check box before pressing SUBMIT.

Mack Corp. Home

 

 

 

 

Data Sheet 9261
Page 1
Index Page Mack Corp. Home Next Page Wall Chart Click robot for printer friendly page

 


Copyright Information Privacy Statement Warranty
© 2000 Mack Corporation